* You can use our Maximo new generation solvent-based liquid glass transparent protective product,
which provides high chemical and physical resistance after 6 to 24 hours,depending on the
ambient temperature, on the floor where Bianca Stella paint application has been completed.
It is applied by mixing the A component and B component of the 2-component product.
Apply the mixture by spreading it with the help of a velvet roller within 30 – 40 minutes.
You should be careful not to make brush and roller strokes on the dry spots.
Thanks to Maximo’s unique and high-performance formula, one coat is sufficient for 4 – 6 m² of area.
If you prefer to apply 2 coats, enough separate mixture should be made for each coat.
A new mixture should be made after 2 to 4 hours according to the ambient temperature and
the second layer should be applied..
** Application surfaces should not be used for 1 day, and surfaces exposed to water should not be used for 2 days.
*** Water should not be allowed to accumulate for the first 7 days, it should be protected against impacts.
After 7 days, you can use chemical cleaners according to the points specified in the “
things to pay attention to after application” section of the detailed explanation below.
DETAILED APPLICATION INFORMATION
How to paint countertops with Stella?
Thanks to the superior and unique formula of Bianca Stella Pure Acrylic Paint, you can easily renew your granite, tile, marble, cement (quartz), acrylic (corian), laminate, solid wood, stainless steel, brass countertops without breaking them.
Required materials for application
Moher roller or velvet varnish roller is a silk brush for narrow and protruding areas, depending on the surface to be applied.
Preparation before Stella paint application
The surfaces to be applied should be cleaned of all kinds of dust, dirt and oil, and sandpaper should be done when necessary. Since paint cannot adhere to oily, silicone and residue areas, the surface must be cleaned with chemical cleaners and degreaser should be used when necessary. Since the paint cannot adhere to areas that are not cleaned well, the application is repeated after the problem area is cleaned and dried.
The most important preparatory step before the paint application is cleaning. You can also complete this step using vinegar. If there is a floating, raised or swollen part on the surfaces to be painted, it should be repaired.
After cleaning, make sure that the environment is completely dry. If necessary, the surface should be dried with a dryer.
Stella Paint application
With 1 liter of Bianca Stella, you can paint 10 – 12 m² of area in two layers. Stella is ready to use. Mix until it becomes homogeneous without thinning. Pour enough paint into a suitable tray.
Complete the first coat application with a mohair roller or velvet varnish roller, which gives the best results on the surface, and a silk brush in narrow and protruding areas where the roller cannot reach. Using your brush and roller at right angles with enough paint is very important for surface smoothness. Apply your paint to the surface at the appropriate rate and be careful not to make brush and roller strokes on the dry spots.
In suitable weather conditions, you can switch to the second coat application after 2 – 3 hours.
If a wooden pattern application is to be made, the generally preferred floor colors are tones such as paper bag and sandbeige.
Wooden pattern image with Stella wood colors
After 3 hours, you can give a wooden look with Bianca Stella wood colors on the counter, whose subfloor application is finished. (optional)
Pour the required amount of Stella wood color into an empty container and add water at the same rate and mix until it becomes homogeneous. Always apply in one direction and as a single layer, always staying on the same plane with the help of a shortcut brush or sponge.
Maximo Protective Liquid Glass application
You should use our Maximo Liquid Glass transparent protective product on Bianca Stella paint to make it more useful.
Bianca Maximo Solvent Based Liquid Glass is a two component product.
Mix component A (large amb.) with component B (small amb.) for application. Mix the mixture for 30 – 40 minutes. Apply it by spreading it with the help of a velvet varnish roller. Take care not to make repeated brush and roller strokes on the dry spots.
With Maximo’s high performance, one coat is sufficient.
If 2 coats are preferred and the product you have is sufficient:
For 1st layer application, mix half of component A (large amb.) and half of component B (small amb.). For the 2nd layer application, mix and apply the remaining amount in the same way after 2 – 4 hours.
(maximo can be applied to 4 – 6 m² area in one coat)
Things to consider after application
First 2 days
Application surfaces should not be used for 1 day, and surfaces exposed to water should not be used for 2 days.
First 7 days
Water accumulation should not be allowed. The wetted area should be dried with a dry cloth or paper towel. It should be protected against impacts, heavy objects should not be placed on the surface, should not be pushed or pulled.
After 7 days
It is not recommended to use bleach directly after the application is completed. If it needs to be used, it is recommended to be diluted with water. Detergent, oil remover, stain remover, dish soap, vinegar water and similar can be used during cleaning. Dish sponge can be used. Wire should not be done. It should not be contacted with lime remover, salt spirit, sink opener, substances containing high percentage of alcohol, thinner, disinfectant.
